点击图片查看原图
1.LED新型彩屏显示。
2.微电脑智能化控制。
3.七档功率调节。
4.采用奇畅Q型专利加热技术。
5.内置防电墙。
6.无水垢设计。
7.超温保护、干烧保护。
8.故障自检功能，并显示故障代码。
型号：DSSK-60 DSSK-70 DSSK-80
颜色：珍珠白、闪光银
外壳尺寸：245*80*370(mm)
配置：
不锈钢双扣软管一条
豪华型花洒
豪华型升降杆
水温调节阀一个
档位热水器系列使用说明 1．功能键 3 个： 1）按键 " 开关 " （ON/OFF） 2）按键“▼”表示降档键（左边键） 3）按键“▲”表示升档键（右边键） 2．使用方法： 1）接通电源 2）按“开关”键（或可先通水） 3）按“▲”升档键和“▼”降档键，调整合适的水温，共7档。 4）可以通过进水阀控制流量，以达到辅助调节水温的目的。 5）中间暂停使用时，可以按“开关”断开电路或关闭进水阀，使机器进入待机状态。 6）长期不用请关闭总电源。 3．使用功能和彩屏显示： 1）接通总电源后，蜂鸣器响一声，彩屏右边两个8字显示出水温度。 2）按“ON/OFF”键，蜂鸣器响一声，彩屏显示各种动感彩灯， 3）打开进水阀通水，蜂鸣器响一声，彩屏显示花洒标志，或通水彩灯标志。 4）按“▲”升档键或按“▼”降档键，每按一次蜂鸣器均响一声，彩屏左边8字显示设定档位。 5）也可以按“ON/OFF”后，设定好合适的档位，再开水阀，通过调节水流量来调节水温。 6）当水温超过65℃时，超温保护自动启动，蜂鸣器响三声，停止加热，彩屏显示“超温”标志和“E1”代码，此时不必关机，当水温低于50℃时，系统自动按设定的档位恢复工作， 7）使用过程中如果直接关闭进水阀暂停用水时，机内水温会升高，再次使用时应避免高温水，注意安全。 8）停止使用时，先按“ON/OFF”键，关闭加热，数秒后再关闭进水阀，这样可以不浪费热水和更好地保护机器。 9）关水关电，通水通电。 10）离开时关闭总电源。 User Manual of Adjustable Water Heater 1. Three Function Buttons 1) Power: (ON / OFF) 2) "▼" : downshift button (left button) 3) "▲" : upshift button (right button) 2. Usage: 1) Switch the power on. 2) Press the "Power" button (or inlet water) 3) Press "▲" upshift button or "▼" downshift button to adjust the temperature, total 7 grades. 4) Control the flow through the inlet valve to assist the water temperature adjustment. 5 Press "Power Off” or close the inlet valve when suspending using the heater, so the machine will be in standby. 6) Please turn off the power when the machine will not be used in a long term. 3. Functions and colorful screen display: 1) After connecting to the power, the buzzer will ring for once with the right side of colorful screen displaying the water temperature by two digits. 2) Press "ON / OFF" button, the buzzer will ring for once with the colorful screen displaying all kinds of dynamic lights 3) Open the water inlet valve, the buzzer will ring for once with the colorful screen displaying the shower or water inletting marks. 4) Press "▲" upshift button or "▼" downshift button, the buzzer will ring for once every time with the left side of the colorful screen displaying the setting grade by one digit. 5) Press "ON / OFF" button and set the appropriate grade, then open the inlet valve to adjust the temperature by water flow. 6) When the water temperature exceeds 65 ℃, it will stop heating with over-temperature protection automatically starting and buzzer ringing for three times. The colorful screen will display "over temperature" signs and "E1" code but it is not necessary to turn off the machine. When the water temperature is below 50 ℃ , the system will automatically rework according to the setting grade. 7) The temperature of water inside the machine will increase when you closing the water inlet valve. Please pay attention to the hot water for safety sake when you reuse it . 8) When you stop using the heater, please press "ON / OFF" button, turn off the heater, then after a few seconds, close the inlet valve to prevent water wasting and protect the machine. 9) Turn off the electricity after closing the water inlet valve, turn on the electricity after opening the water inlet valve 10) Turn off the power when you are away from the machine.
